Keiurot 6 x 12V LED Strip Lights (Pink) for Car/Motorcycle Interior, 30cm Waterproof IP67, 5050 12SMD

The essentials

These Keiurot 6 x 12V LED strip lights are a set of thin, flexible interior strips aimed at adding a visible glow inside a car, motorbike, or other DC 12V vehicle setups. The pitch is pretty clear: you get multiple 30cm sections, they’re described as waterproof with an IP67 rating, and the strips use 5050 12SMD LEDs in a pink/purple colour tone.

On paper, it’s a straightforward way to brighten up footwells, under-dash areas, storage compartments, or even small underbody/exterior accents—without having to commit to a full custom lighting kit. That flexibility (literally cuttable, with the note about cutting along the resistant line) makes it easier to adapt to your layout.

Key features

What stands out first is the mix of “thin + flexible + cuttable”. The strips are described as ultra-thin and able to sit between gaps so they’re “virtually invisible” once installed. They’re also meant to be cut to the length you want, as long as you cut on the cut-resistant line.

They’re also marketed as UV & water resistant with IP67 waterproofing. In practical terms, that’s the sort of spec you look for when the installation might be exposed to damp, splash zones, or outdoor vehicle environments.

What to know before you buy

There are a couple of details worth taking seriously, because they can make or break an installation.

First, power and wiring: the description says it’s a 12V DC strip and that you need to respect polarity. If it doesn’t light, you’re advised to reverse the polarity. The lead wire length is given as 23.5cm, with black as negative (-) and red as positive (+), so you’ll want to plan where your power feed lands.

Second, the current draw is stated as “0.07A @ 12V-DC”. That doesn’t tell you everything about your vehicle’s wiring, but it does hint that this is intended to be used as low-power accent lighting rather than the kind of illumination you’d rely on as primary lighting.

Third, adhesive installation: the strips are described as having strong adhesive tape. Adhesive works well when the surface is clean and dry, but it can be less forgiving on textured or dusty areas—so don’t treat it like it’s guaranteed to stick everywhere.

Finally, the colour: the set is described as pink/purple. If you’re after a neutral white or a blue tint, this probably won’t match what you’re imagining.

Pros and where it shines

If you like the idea of discreet lighting tucked under dashboards, around footwell edges, or hidden in small exterior grilles/underdash spaces, this type of strip tends to be more practical than bulkier lighting bars.

Key strengths suggested by the listing: - IP67 waterproofing (plus UV and water resistance claims), which makes it more suitable for splash-prone installs than basic indoor-style strips. - Flexible, ultra-thin build meant for fitting into gaps. - Cuttable to fit your chosen route, as long as you cut along the resistant line. - A multi-pack of 6 strips, which helps if you’re mapping lighting across several areas rather than just one.

A micro example: if you’re installing under a motorbike dashboard, you can run one 30cm strip along the underside, tuck it into a narrow gap near the controls, then use a second strip for the opposite side—keeping the wiring tidy with the provided lead wire lengths.

When it might not be a great match

It’s not ideal if you’re expecting a premium, “plug-and-forget” system that you can hide perfectly with zero prep. Adhesive-only fitting depends quite a bit on the surface condition.

Also, while it’s marketed for a wide range of applications (cars, motorcycles, boats, cargo trailers, camper-vans, and more), the listing doesn’t spell out installation accessories beyond connecting to 12V DC. So if you need a full wiring harness, connectors, or a controller for effects, you may end up needing extra parts.

And if you’re building an ultra-bright lighting setup, remember the stated current draw is modest, this reads more like accent/atmosphere lighting than high-output illumination.

How to make it work in real life

Plan the route first, then cut. Because the strips are cuttable, you can trim to your lengths, but you should follow the instruction to cut on the cut-resistant line.

Next, check polarity before you fully commit. The listing specifically warns that if it doesn’t light, reverse polarity—so test with power connected briefly before leaving the adhesive to set.

Finally, keep wiring slack in mind. With a 23.5cm lead wire length, you’ll want a reasonable path from your mounting point back to the power connection.

Should you buy it?

This is worth considering if you want a set of thin 12V LED strip lights in pink/purple for discreet interior accent lighting, and you’d like the added reassurance of an IP67 waterproof rating for damp or outdoor-ish setups.

It might not be the best choice if you need a colour other than pink/purple, you’re not comfortable planning wiring/polarity, or you’re expecting high-output lighting performance. It’s also less suitable if your mounting surfaces are likely to be hard to stick to without preparation.

So, if your goal is under-dash, footwell, or underbody-style ambience—and you’re happy to do the fitting and basic electrical connection—this set fits the job description.

FAQs

What power does it need?

It’s described as a 12V DC LED strip, with a note that you should reverse polarity if it doesn’t light.

Can the strips be cut to size?

Yes. The listing says it can be cut to the length you want, but you need to cut along the cut-resistant line.

Is it suitable for wet locations?

It’s marketed as waterproof with an IP67 rating, and also described as UV & water resistant.

How long are the lead wires?

The lead wire length is listed as 23.5cm.

Will it come with all six strips?

Yes. The package is described as including a 6-pack of 30cm pink/purple LED strip lights for 12V use.