ARCCAPTAIN CUT60 Non-HF Plasma Cutter, 60A, 4-in-1, 110V/220V
Product description
A plate-only cutter serves a narrower set of tasks. The ARCCAPTAIN CUT60 Non-HF brings plate cutting, expanded-metal cutting, rust and paint removal, and plasma gouging into one machine. Its 110V/220V input and blowback pilot arc support a range of metalworking setups. An LED display puts operating information in view as you work.
Key features
Four cutting modes help handle more than straight cuts through plate. Expanded-metal mode is designed to maintain an arc across mesh, while rust-clean mode removes corrosion and coatings without grinding. Plasma gouging can remove old welds, address defects, and prepare bevels for repairs, change the nozzle when using gouging mode.
The non-HF blowback pilot arc starts without the electromagnetic interference associated with HF machines. The IPT60 torch has a non-contact pilot arc for work on rough, painted, rusty, or dirty surfaces. Cutting capacity depends on input voltage: at 110V, the maximum cut is 5/8" and the clean cut is 1/2", at 220V, the maximum cut is 1-1/16" and the clean cut is 3/4". The machine cuts steel, stainless steel, aluminum, and other metals.
A large LED display shows air pressure in real time. Pressure below 30 PSI triggers an E80 warning, and pressure above 80 PSI triggers E81. Recommended pressure is 55 PSI at 110V and 50–75 PSI at 220V. The preinstalled air filter uses a 1/4" NPT quick-connect fitting. An external air compressor is required and sold separately.
Practical tips
Match the power input and cut settings to the material and task. The listed cutting ranges are 12–16mm at 110V and 20–28mm at 220V. Pressure-detection mode lets you check air pressure before cutting. PA (pilot arc) time adjusts from 2–10 seconds, and PT (postflow) time adjusts from 5–15 seconds to cool the torch. Use 2T for short or precise cuts, 4T starts and stops with separate presses, which can reduce hand fatigue during longer continuous cuts.
The package includes the plasma cutter, an IPT60 torch, an earth clamp, an air hose, four nozzles, and two electrodes. It also includes two 0.9 mm and two 1.1 mm nozzles. Overload, overheat, and overcurrent protections provide error codes, with an IGBT low-voltage warning as well.
Who it’s for
This machine suits home garage and workshop users who work on different metal-cutting and repair tasks, rather than only making straight plate cuts. Expanded-metal mode is relevant for mesh projects, rust-clean mode and gouging add options for restoration and weld repair. Buyers who need to work across 110V and 220V inputs can choose settings and cutting capacity to match the available input and job.
Buyer feedback is positive about the machine overall, while reliability impressions are mixed. Some buyers report that it works well, others mention issues with the machine refusing to reset. The included torch and consumables make the package relevant to users assembling a plasma-cutting setup, with an external compressor needed for operation.
Practical questions
What can the CUT60 cut? It is listed for steel, stainless steel, aluminum, and other metals. Maximum and clean-cut thicknesses vary by input: 5/8" maximum and 1/2" clean at 110V, 1-1/16" maximum and 3/4" clean at 220V.
What air supply does it need? It requires an external air compressor. Recommended pressure is 55 PSI at 110V or 50–75 PSI at 220V, and the display monitors pressure during operation.
Can it cut expanded metal and remove old welds? Yes. Expanded-metal cutting and plasma gouging are among its four modes. Replace the nozzle when using gouging mode.
Should you buy it?
Choose the CUT60 Non-HF if your projects range from plate and mesh cutting to coating removal and weld repair. Its four modes, voltage-dependent cutting capacity, adjustable arc and postflow settings, and included IPT60 torch make it a practical fit for varied garage or workshop metalwork.