TAILONZ PNEUMATIC PL6-03 male elbow push-to-connect fitting for 6mm tube (3/8" BSP), 10-pack
Product description
If your pneumatic line needs a tidy turn without fussing over threads, this TAILONZ PNEUMATIC male elbow is designed for push-to-connect setups. On paper, it’s aimed at simple routing changes using 6mm tube (tube OD), with a male 3/8" BSP connection for hooking into your existing system.
That said, fittings are one of those areas where small details matter—especially tube type, temperature limits and pressure rating. Get those right and it can be a practical time-saver. Miss them, and it may feel like an expensive lesson.
The essentials
This male elbow is a push-to-connect pneumatic fitting, built to join your 6mm tube OD to a 3/8" BSP male connection. The material mix is listed as copper and plastic, and it’s positioned for everyday pneumatic use rather than demanding industrial extremes.
It’s rated for a maximum pressure of 0~1MPA and a working temperature of 0~60°C. It also specifies which tubing you can use: PU, PA, PE and PVC. If your setup matches those basics, it’s a straightforward way to create an angle turn in the line.
What you’ll notice in use
The main appeal of push-to-connect fittings is convenience. Instead of dealing with complicated assembly, the tube is pushed into the fitting to form the connection—useful when you’re refurbishing a run, reorganising pipework, or replacing a failed elbow quickly.
A practical example: imagine you’re setting up a small workshop pneumatic circuit and you need to route air around a frame or machine corner. Swapping to a male elbow for a 90° direction change can keep the layout cleaner and reduce strain on hoses compared with bending them too sharply.
Where it can feel less “effortless” is when installation conditions aren’t ideal. Any mismatch between your tube outer diameter, tube type, or seating depth can affect how secure the connection feels.
Key specifications that affect fit
Below are the details that matter most when deciding whether this will suit your system.
Tech specs
- Name: TAILONZ PNEUMATIC Male Elbow Push to Connect Fittings (PL6-03)
- Type: Male elbow push-to-connect fitting
- Material: Copper and plastic
- Size: 6mm tube OD x 3/8 inch BSP
- Maximum pressure: 0~1MPA
- Working temperature: 0~60°C
- Applicable tube: PU / PA / PE / PVC
Where it makes sense (and where it might not)
It’s a good fit if you want a simple male elbow for a push-to-connect pneumatic setup and your tubing is one of the listed types (PU/PA/PE/PVC). It also makes sense if your operating conditions sit within the stated pressure (0~1MPA) and temperature range (0~60°C).
Not the best choice if your system needs higher pressures, runs outside the temperature limit, or uses a tube material not covered by the specification. Also, because this is a 3/8" BSP male interface, you’ll need your counterpart to be compatible with that thread standard—if it isn’t, you may end up needing an adapter rather than a direct install.
What to check before buying
Before ordering a pack of 10, it’s worth double-checking:
- Tube type and tube OD: The fitting is for 6mm tube OD, and the compatible tube materials are explicitly given. If your tube isn’t listed, don’t assume it will still seal.
- Pressure and temperature: This has a maximum pressure of 0~1MPA and working temperature up to 60°C. If your application runs hotter or higher pressure, it could be a mismatch.
- Thread compatibility: The connection is 3/8" BSP male. Make sure the receiving port on your manifold or equipment uses the right standard.
Buying verdict
Should you buy it? It’s a practical pick for routine pneumatic pipework where you’re using 6mm tube OD from the specified materials and you want a push-to-connect male elbow for direction changes. The material choice (copper and plastic) and the stated 0~1MPA / 0~60°C limits suggest a “keep it within the brief” style of component.
You may want to skip it if your application is on the edge of its pressure/temperature limits or if your tubing or connection standard doesn’t match what’s listed.
Quick FAQ
Is this a push-to-connect fitting or a threaded fitting? It’s described as a male elbow push-to-connect fitting for 6mm tube OD, with a 3/8" BSP male connection interface.
What tube types can it be used with? The specification lists PU, PA, PE and PVC.
What are the pressure and temperature limits? Maximum pressure is given as 0~1MPA and working temperature as 0~60°C.
How many fittings come in the pack? It’s supplied as a pack of 10.