febi bilstein Anti Roll Bar Bush Kit 19 mm
Product description
Anti roll bar bush replacement matters when you notice more movement than usual from the rear axle, or when handling feels less settled than it used to. The febi bilstein 44860 Anti Roll Bar Bush Kit with brackets and screws is a practical maintenance part designed to help restore proper anti roll bar positioning. It includes the bushes plus the brackets and screws, so you have the key fastening components in one kit 🛠️.
With its inner diameter of 19 mm, this kit matches specific fitment requirements on the rear axle, on both sides. If you are planning a rear suspension service, having the correct dimensions and fitting side can make the difference between a smooth job and wasted time. Keep in mind that compatibility depends on your vehicle, so it is worth checking against your vehicle identification before ordering ✅.
Key features
This anti roll bar bush kit by febi bilstein is supplied as a single pack, combining the bush components with the brackets and screws you need for installation. The inclusion of brackets and screws helps reduce the chance of missing small but necessary hardware during a workshop or DIY job. It is a spare part built for vehicle repair and maintenance, and febi bilstein supplies many parts designed for fitment by reference to OE listings.
The kit specifies an inner diameter of 19 mm, which is a key measurement for correct seating and alignment. It also states that the fitting side is the rear axle on both sides, which is useful when you are replacing bushes in pairs rather than patching one side only. In everyday terms, correct bush seating supports consistent suspension feel, especially over uneven road surfaces.
Because suspension components are safety critical, double check that the part matches your vehicle specification. The manufacturer notes that you should use the vehicle identification information to confirm compatibility, and that all restrictions must be observed. That step is particularly important when you are working on older models or vehicles with different variants.
If you want to keep your maintenance approach tidy, a complete kit can simplify parts management. You can order one pack rather than sourcing separate bushes and fasteners, which is often the quickest route to getting the job finished. 🧰
What you get and what to check before fitting
The febi bilstein 44860 is described as an anti roll bar bush kit with brackets and screws, supplied in a pack of one. The stated weight is 0.562 kg, which can be relevant for logistics when you are planning shipping or workshop deliveries. The kit also includes OE numbers for comparison purposes only, such as VW 2K0 511 413 D S1 among others.
Before you fit anything, confirm the exact fitment details. The product information highlights an inner diameter of 19 mm and a rear axle both sides fitting location. If your vehicle specification does not align with those details, the kit may not be the right match even if the general category sounds correct.
It is also sensible to verify vehicle compatibility using the vehicle identification at the top of the product page, as the manufacturer specifically advises this. Observe any restrictions and do not assume that all similar models share the same anti roll bar bush configuration. Suspension setups can vary by trim level, production year, and regional specifications.
In addition, plan your fitting session with the right tools and workshop procedures for suspension components. Anti roll bar bush replacement often involves careful positioning and torque practices to keep everything aligned. If you are doing it yourself, take your time, compare parts on the bench, and follow the correct vehicle repair guidance.
Worth noting: if you only replace one side, you may not see the same improvement as a matched pair, so the both sides specification is a helpful clue. If you prioritise a balanced rear axle feel, replacing both sides as part of the same job can make more sense.
Tech specs
- Name: febi bilstein 44860 Anti Roll Bar Bush Kit with brackets and screws
- Type: Anti Roll Bar Bush Kit
- Inner Diameter: 19 mm
- Fitting Side: rear axle both sides
- Weight: 0.562 kg
- Pack Quantity: pack of one
- OE numbers: VW 2K0 511 413 D S1 among others
Who it’s for
This kit suits owners and mechanics who need a direct replacement anti roll bar bush solution for the rear axle on both sides. It is particularly relevant if you are maintaining a VW Caddy 3, including versions such as Caddy 3 2C and Caddy 3 2K, based on the suitability notes provided. If you are already working on rear suspension and want the brackets and screws included, this format can fit naturally into a maintenance plan.
It may not be the best match if your vehicle specification does not align with the stated 19 mm inner diameter or the rear axle both sides requirement. You may also want to skip it if you cannot confirm compatibility using your vehicle identification, because the manufacturer highlights the importance of checking restrictions. For anyone focused on correct fitment and straightforward installation parts supply, febi bilstein 44860 is a sensible option to consider.