Double Sided Sticky Pads (10 Pack) Heavy Duty Acrylic Foam Pads for Dash Cam & Action Camera – 50×25mm
Product description
What these double sided sticky pads are for
If you’re trying to mount a dash cam, action camera, or similar gear without drilling, double sided sticky pads like these are exactly the kind of accessory that gets used a lot at home, in the office, and on the move. The idea here is simple: you stick one side to the camera mount (or the surface it’s meant to sit on), press the pad down to fully compress it, and you get a bonding layer designed to hold steady during use.
On paper, this is built around an acrylic foam core with a closed cell structure. That matters because foam pads can cope better with small irregularities on surfaces than rigid tape alone, which can help with contact area and overall grip.
The essentials: adhesion, temperature and water resistance
The headline claim is strong adhesion. These pads use an acrylic material with a polymer adhesive and a closed cell structure, aimed at keeping an action camera securely in place even when things get bumpy. The description also suggests the bond can strengthen over time, which is useful if you want the mount to feel more secure after it’s been left to settle.
Where these pads lean more “serious accessory” than basic craft tape is the environmental resistance: the foam structure is described as resistant to water, temperature, moisture and solvents. It also notes an application temperature range of -15°C to 121°C, and adds a practical tip for colder conditions: if you’re below 15°C, you can warm the surface with a hairdryer to improve adhesion.
One limitation worth bearing in mind: although the pads are described as water and temperature resistant, they’re still adhesive pads. If your surface is dusty, oily, or not solid, results can vary.
What you’ll notice in use (and the trade-offs)
These pads are square shaped and designed to be hand torn, which is handy if you ever need to adjust the size. The foam core has flexibility designed to fill uneven surfaces, and the description says the tape can stretch (over 30%) as needed. In real terms, that means you’re less likely to end up with a tiny, perfectly-cut piece that doesn’t fully sit flat.
They’re also designed to remove without residue. The description states you can tear them off without leaving residue and without damaging the surface of the object. That’s a big deal if you like the idea of mounting something now, but you don’t want a permanent sticky mess later.
That said, it’s not the best fit for every scenario: the guidance explicitly notes it’s not recommended to use the dash cam sticky pad on walls that aren’t solid, so it doesn’t pull the wall covering down.
Key features that matter for buying decisions
Technical details
- Type: Double sided adhesive pads (acrylic foam)
- Quantity: 10 pcs
- Size: 50×25mm
- Material: Acrylic foam with a closed cell structure
- Adhesion: Polymer adhesive designed for strong bonding
- Water & temperature resistance: Closed cell structure described as resistant to water and temperature
- Application temperature: -15°C to 121°C
- Adhesion tip for cold use: Warm surface with a hairdryer if below 15°C
- Removal: Designed to be removable without residue
- Mounting notes: Not recommended on walls that are not solid
- Shape / handling: Square shaped with hand tearing bit
Pros vs cons in plain English
What stands out - Strong-adhesion focus for holding cameras securely while in sports or motion. - Closed cell foam aims to resist water and moisture, and handle a wide application temperature range. - Foam flexibility helps fill uneven surfaces, which can improve bonding area. - Removal is designed to be residue-free (useful if you change setups).
What to be careful about - Adhesives are only as good as the surface prep: if the surface isn’t solid or is contaminated, you may not get the result you expect. - If you’re thinking about wall mounting, the product description specifically warns against non-solid walls.
When it makes sense (and when it doesn’t)
It’s a good fit if you want a convenient mounting method for an action camera or dash cam where drilling isn’t appealing. It also makes sense if you’re dealing with outdoor-ish conditions (moisture, sun heat, temperature swings) and you want the pad to stay tacky rather than drying out quickly.
You might want to skip it if your mounting surface isn’t solid (especially for walls), or if you’re expecting it to replace proper mechanical mounting in high-stress or safety-critical setups. It’s built to bond and stay put, but like most adhesive systems, it depends quite a lot on surface condition and correct compression.
If you prioritisе quick repositioning or residue-free removal as a requirement, these pads are more aligned with that goal than many traditional tapes that can leave marks behind.
Practical tips for getting the best bond
Before sticking anything down, take a moment with surface prep—wipe away dust and grease where relevant. Once you place the pad, press it so it fully compresses (the description says it bonds quickly and securely when fully compressed). If you’re working in cold weather, use the hairdryer tip to warm the surface before applying.
For a micro example: imagine you’re setting up an action camera for a day out. You tear the pad to size (or stretch it slightly), stick it to the mounting area, peel the release paper, then press the camera mount firmly into place. After that, give it time to settle rather than tugging immediately.
Should you buy it?
For most people using it as a non-drill mount for a dash cam or action camera, these double sided sticky pads look like a practical buy: they’re designed around foam flexibility, strong polymer adhesion, and resistance to water and temperature swings.
It’s not the best match if your plan involves sticking to non-solid walls, or if your surfaces are questionable. Also, if you need a guaranteed, permanent fixing with zero dependence on surface condition, you may feel more comfortable with a more mechanical approach.
If you’re after a residue-free mounting solution that’s meant to hold up during everyday motion and sports use, it’s worth considering—just keep expectations realistic and focus on prep and proper compression.
Mini FAQ
What surfaces is this supposed to bond to?
The description talks about mounting cameras and also warns against using it on walls that aren’t solid. Beyond that, it’s mainly about getting good contact and fully compressing the pad on the surface you’re sticking to.
Does it work in cold weather?
It includes guidance for cold use: if the temperature is below 15°C, warm the surface with a hairdryer before applying for better adhesion.
Will it leave residue when removed?
The description states it can be torn off without residue and without damaging the surface of the object.
Is it waterproof?
It’s described as resistant to water and moisture thanks to the closed cell foam structure, but it’s still an adhesive product—surface quality will influence real-world results.
How long does it take to bond?
The description suggests it bonds quickly once fully compressed, though stronger holding over time is implied.