Boobrie 30cm SMA Male right-angle to SMA Female RG316 extension cable (2-pack) for WiFi/LTE routers
Product description
What it is and why people buy it
This Boobrie SMA extension cable is designed to go from an SMA male connector with a right-angle end to an SMA female bulkhead-style connection, using RG316 coax. On paper, that combination is all about solving one common install problem: you need a flexible RF lead that can reach your router, booster or external WiFi/LTE antenna without fighting awkward spacing.
Because it uses a right-angle SMA male, it can be a practical way to keep cabling tidier when your antenna ports are hard to access or sit close to a case edge. And since RG316 is positioned here as a low-loss, flexible coax option, the intent is that it stays suitable for typical RF/antenna runs (rather than being only for short bench experiments).
Key features that matter in real installs
You’re basically getting a compact 30cm coax extension made for 50 ohm RF use, built around RG316. The connectors are described as copper with good connectivity, and the surface treatment is gold-plated. There’s also mention of a military-spec style conformity for the RG316 cable and a PTFE dielectric, which (again, on paper) supports low-loss, high-frequency suitability.
Two more practical details: - The package includes a pack of 2 cables, which is handy if you’re doing one installation now and want a spare for the next tweak. - The product is described as having over 1000 mating life time, which is relevant if you expect to adjust connections more than once.
That said, it’s not perfect for every use case. The description explicitly notes that this SMA cable is not fit for TV—so if your project is TV antenna specific, you’d need to look for the right connector type instead.
Where it shines (and what to watch)
If you’re setting up or upgrading WiFi antenna, WLAN, a booster, or other mobile/router RF arrangements, this cable looks aimed at day-to-day connectivity work. The short length and flexible RG316 style also make it more forgiving when routing cable around a router location or along a wall.
What you’ll likely notice day to day
In typical installs, you care less about marketing and more about two things: getting a clean mechanical fit and having a cable that behaves itself during routing. A right-angle connector helps with clearance, while the stated low-loss RG316 approach is there to keep performance as sensible as the cable allows.
A limitation to keep in mind
You may want to skip it if you’re trying to use it for TV antenna setups, because the connector pairing here doesn’t match that need.
Specs in plain English
This is an SMA Male (right angle) to SMA Female extension cable built with RG316 coax, 50 ohm. The cable length is 30cm, and it’s supplied as a 2-pack.
If you’re buying based on frequency expectations, RG316 is mentioned as low-loss and high-frequency suitable, and the dielectric is described as PTFE with a conductor made from seven strands. There’s also a note that RG316 is suitable for burial and a wide temperature range—useful context if your installation is more outdoors or less “office tidy”.
Who it’s for (and who should look elsewhere)
It makes sense if you’re trying to connect a router/booster setup to an external antenna where you need a short, flexible lead and a right-angle SMA male end to manage space.
It might not suit you if: - your project is TV-focused (the description says it’s not fit for TV), - you need a different cable type/impedance/connector format than what’s stated, - you’re expecting a long run—30cm is small by design, and longer distances may call for a different approach.
If you’re just shopping in the “RF cables in general” bucket, it’s worth checking whether your device’s antenna port is truly SMA male/female in the way you need. With coax, getting the connector gender and style right matters as much as the cable material.
Getting the most from it
Before you buy, double-check three things so you don’t waste time: - Connector type: this is SMA male (right angle) to SMA female. - Cable length: 30cm only—measure your route and allow a little slack. - Impedance expectation: it’s specified as 50 ohm, so make sure your antenna system is in that same ballpark.
A quick micro-scenario: imagine mounting a WiFi antenna near the edge of a router’s enclosure. Straight connectors often force the cable to kink or press against the case. A right-angle SMA male end can let you route the lead down and away more naturally, while the 30cm length keeps the run compact.
Mini FAQ
Is this cable suitable for WiFi and LTE antenna set-ups?
It’s commonly described as used for router/booster/WLAN/WiFi antenna and mobile antenna applications, so it aligns with those kinds of RF coax runs.
What length do I get?
The cable length is 30cm.
Does it work for TV antenna connections?
No—the description specifically says it is not fit for TV.
What’s in the pack?
You get a pack of 2 RG316 SMA right-angle to SMA female low-loss cables.
Final verdict
It’s a solid buy if you’re building a compact 50 ohm RF connection for a router/booster/WiFi or LTE antenna run and you need the right-angle SMA male to fit where space is tight. The RG316 + PTFE dielectric + low-loss intent makes sense for typical antenna cabling, and the 2-pack gives you some breathing room.
However, if your goal is a TV antenna connection, you should look elsewhere first. And if your installation needs a longer reach than 30cm, it may not be the best match—at that point, the cable length becomes a bigger constraint than the coax quality.